Bellows

MULTIPURPOSE BELLOWS 4x5″/10x12.5 cm 454.11
Camera bellows for the 4x5″/10x12.5 cm Sinar f1, f2, x, p2 and e. Used with multi-purpose standards for increasing the bellows extension for all formats and as a light hood for viewing the image on the focusing screen and also as a lens hood.
The snap fit on its frame permits easy attachment to Filter Holders 1 or 2 (547.11 or 547.21 respectively).
Maximum extension is 45 cm (18″).



TAPERED BELLOWS 5x7″/13x18 cm 452.17
For extensions up to 50 cm (20″) with the 5x7″/13x18 cm format. For longer extensions, an aditional Multipurpose Standard 437.61 and a Multipurpose Bellows 454.11 are needed. Also serves as a light hood for viewing the image on a 5x7″/13x18 cm focusing screen.






TAPERED BELLOWS 8x10″/20x25 cm 452.58
For extensions up to 65 cm (25²) with the 8x10″/20x25 cm format. Fits on Carrier Frame 433.58 and on 8x10″/20x25 cm Metering Back 462.58. For a further extension from 65 to 90 cm (25 to 35″), an additional Multipurpose Standard 437.61 and a Multipurpose Bellows 454.11 are needed.







SPECIAL BELLOWS 8x10″/20x25 cm to 5x7″/13x18 cm 453.58
For bellows extensions beyond 90 cm (36″) with the 8x10″/20x25 cm format. A 5x7″/13x18 cm Multipurpose Standard and a 5x7″/13x18 cm Tapered Bellows are required as intermediate bellows support.
Additional bellows extensions are possible by adding more multipurpose standards and multipurpose bellows.







WIDE ANGLE BELLOWS 1 4x5″/10x12.5 cm 455.36
For short bellows extensions with the 4x5″/10x12.5 cm format. For use with focal lengths from 75 to 135 mm focused at infinity. Good camera adjustment capability is retained in spite of the short exten-sion.
• Also serves as a hood while viewing an image on the focusing screen, for example with Binocular Magnifier 471.21 and Binocular Light Hood 531.51.





WIDE ANGLE BELLOWS 2 4x5″/10x12.5 cm 455.46
This wide angle bellows is required for 4x5″/10x12.5 cm format photography in conjunction with extreme wide angle lenses (65 mm or shorter), for extreme camera adjustments and for digital photography with CCD array chips.






WIDE ANGLE BELLOWS 5x7″/13x18 cm 455.27
For very short bellows extensions with the 5x7″/13x18 cm format and focal lengths from 90 to 165 mm focused at infinity. Permits good camera adjustments in spite of the short extension.
• Can also be used as a focusing screen viewing hood, for instance with Binocular Magnifier 471.21 and Binocular Light Hood 531.51.




WIDE ANGLE BELLOWS 8x10″/20x15 cm 455.58
For very short bellows extensions with the 8x10″/20x25 cm format and focal lengths from 120 to 240 mm focused at infinity. Fits on Carrier Frame 433.58 and on Metering Back 8x10″/20x25 cm 462.58. Permits good camera adjustments in spite of the short extension.
• Can also be used as a focusing screen viewing hood with the 8x10″/20x25 cm format, for instance with Binocular Magnifier 471.21 and Binocular Light Hood 531.51.

 

PLEASE NOTE: AVAILABILITY MAY BE LIMITED AS MANY ITEMS HAVE BEEN DISCONTINUED!

Bellows Lens Hood

Lens Hood for Sinar p3 / f3

Here you can find all items required to build one of the various versions of a Bellows lens hood for the Sinar p3 and Sinar f3 line of view cameras.

Why use a lens shade?

With an unprotected lens, stray light from outside the subject area can reduce image contrast noticeably and this is why a lens shade is an indispensable tool in professional photography. However, a lens shade can only provide the best protection against stray light when it is optimally tailored to the angle of view, and the Sinar System offers several solutions for that purpose.

 

_______________________________________________________________________________________

Example of a straight Bellows lens hood

When using a Sinar p3 or Sinar f3 camera without the auxiliary of a Sinar LC shutter, a Bellows lens hood can be made using the following items of the Sinar System:

Lens adapter ring appropriate for the lens that is being used
473.41.000 Filter-/Bellows holder
452.16.010 Tapered bellows
472.41.000 Rod holder 100
472.71.000 Filter rod 16 cm
472.81.000 Filter rod 25 cm
473.31.000 Bellows holder clip
531.61.000 Accessory shoe

With the above solution the length of the bellows extension can be adjusted to the needs of the focal length of the lens.

Thanks to the Joint rod, in addition, the bellows extension and also the bellows direction can be adjusted.

One ND filter (Neutral Density) or any other filter of the size 100 x 100 x 1 mm can be inserted in the Filter-/Bellows holder.

If you want to use a Polarizing filter at the same time as the bellows hood, the following items are needed additionally:

472.41.000 Rod holder 100
472.71.000 Filter rod 16 cm
472.81.000 Filter rod 25 cm
546.31.000 Swiveling linear polarizing filter
The Rod holder for the Polarizing filter is mounted on the left hand side of the Carrier frame of the Front standard.

_______________________________________________________________________________________

Example of a Lens hood without bellows

The following solution can be used as an alternative to the above configuration:

Lens adapter ring appropriate for the lens that is being used
493.23.041 Artec Lens Shade
If you want to use a Polarizing filter at the same time as the bellows hood, the following items are needed additionally:

472.41.000 Rod holder 100
472.71.000 Filter rod 16 cm
472.81.000 Filter rod 25 cm
546.31.000 Swiveling linear polarizing filter
The Rod holder for the Polarizing filter is mounted on either side of the Carrier frame of the Front standard.

_______________________________________________________________________________________

 

Example of a Bellows lens hood with LC shutter

When using a Sinar p3 or Sinar f3 camera with the auxiliary of a Sinar LC shutter, a Bellows lens hood can be made using the following items of the Sinar System:

Lens adapter ring appropriate for the lens that is being used
473.41.000 Filter-/Bellows holder
452.16.010 Tapered bellows
472.41.000 Rod holder 100
472.51.010 Joint rod 2
473.31.000 Bellows holder clip
531.61.000 Accessory shoe
With the above solution the length of the bellows extension can be adjusted to the needs of the focal length of the lens.

Thanks to the Joint rod, additionally to the bellows extension also the bellows direction can be adjusted.

One ND filter (Neutral Density) or any other filter of the size 100 x 100 x 1 mm can be inserted in the Filter-/Bellows holder.

If you want to use a Polarizing filter at the same time as the bellows hood, the following items are needed additionally:

472.41.000 Rod holder 100
472.71.000 Filter rod 16 cm
472.81.000 Filter rod 25 cm
546.31.010 Swiveling circular polarizing filter
The Rod holder for the Polarizing filter is mounted on the left hand side of the Carrier frame of the Front standard.

_______________________________________________________________________________________

Lens Hood Components

MULTIPURPOSE BELLOWS 4x5″/10x12.5 cm 454.11
Standard camera bellows for the Sinar f1, f2, x, p2, and e 4x5″/10x12.5 cm. Also serves as a bellows lens hood. The snap fit on its frame permits easy attachment to Filter Holder 1 or 2 (547.11 or 547.21, respectively).





MULTIPURPOSE STANDARD 4x5″/10x12.5 cm 437.61
Multipurpose standard for the professional lens hood. Equipped with shift, swing and tilt movements.








JOINTED ROD 472.51
Forms an adjustable bellows lens hood when used in combination with Multipurpose Bellows 454.11 (or with any Sinar bellows with 4x5″/10x12.5 cm frames) and two Bellows Holders 473.31. The Jointed Rod is equipped with two ball joints that can be locked in position. Extends to approximately 12″/30 cm.
• Can also be used for supporting a wide angle or multipurpose bellows as a focusing screen viewing hood.

ROD, SHORT, 11cm 472.61
ROD, MEDIUM, 16 cm 472.71
ROD, LONG, 25 cm 472.81
In combination with Multipurpose Bellows 454.11 (or with any Sinar bellows with 4x5″/10x12.5 cm frames) and two Bellows Holders 473.31, these rods form a basic bellows lens hood which, however, permits no camera adjustments.
• These rods are also used for supporting Swivelling Linear Polarizing Filter 546.31.
• The use of Jointed Rod 472.51 is recommended when

BELLOWS HOLDER 473.31
Used for attaching a bellows or Bellows Hood Mask 1 or 2 (533.11 or 533.21, respectively) to the camera. Requires the use of one of the rods 472.61, 472.71 or 472.81, or Jointed Rod 472.51.




BELLOWS HOOD MASK 1 533.11
Bellows Hood Mask 1 can be used as a lens hood for wide angle lenses or as a mask holder for special effects. Fits on all Sinar 4x5″/10x12.5 cm standards and on Bellows Holder 473.31.
Consists of two hinged and two sliding panels.






BELLOWS HOOD MASK 2 533.21
With four roller blinds with positioning scales controlled by separate fine adjustment drives, for precise vignetting control.
Recommended for product shots, difficult backlit situations and multiple exposures. Fits on all Sinar 4x5″/10x12.5 cm standards, Bellows Holder 473.31, and on Filter Holder 1 547.11 or Filter Holder 2 547.21. Can be slipped on and rotated.

Camera Supports

 

RAIL CLAMP 2 411.41

For the attachment of Sinar cameras to the Sinar Pan Tilt Head 516.41 or directly to the tripod. For greater stability with long bellows extensions, Clamping Adapter 411.21.010 is used for mounting these Rail Clamps on Base Plate 2 418.31. Fitted with a 3/8″ tripod socket.
• Can be converted to a 1/4″-tripod socket with Reducing Bushing 3/8″– 1/4″ 519.61.
• Rail Clamp 2 has a 360° tensioning mechanism that ensures that the camera retains its horizontal position when the clamp is tightened.

CLAMPING ADAPTER 411.21.010

For mounting a Rail Clamp 1 or 2 on the Base Plate 2 418.31.
• Can also be used for quick attachment of Rail Clamp 1 411.21 or Rail Clamp 2 411.41 to Sinar Pan Tilt Head 516.41 by means of Quick Release Adapter 519.51.

QUICK RELEASE ADAPTER 519.51

For quick mounting of a rail clamp with clamping adapter, or of a Base Plate 2 to Sinar Pan Tilt Head 516.41. Includes a 3/8″ bolt.

BASE PLATE 2 418.31

The camera is mounted on the Base Plate by means of two Rail Clamps 411.21 or 411.41, each equipped with a Clamping Adapter 411.21.010. The Base Plate is attached to the Sinar Pan Tilt Head by means of a Rapid Clamping Adapter 591.51.

PAN TILT HEAD 516.41

Compact and stable Sinar Pan Tilt Head with a sturdy tensioning lever that can be positioned conveniently. Fitted with two positioning studs for fast and easy mounting of a rail clamp.
Comes with a dual camera bolt 1/4″ and 3/8″.
• The head can be smoothly rotated 360° horizontally for precise settings.

(Sorry, no longer available new)

REDUCING BUSHING 3/8″ – 1/4″ 519.61

For the conversion of the standard 3/8″ tripod socket thread from 3/8″ to 1/4″. For use with: Pan Tilt Head 516.41, Rail Clamp 1 411.21, and Rail Clamp 2 411.41.

Film Holders

Every Sinar camera accepts basically all film holders that conform to international standards and that are used on so-called international camera backs.

SINAR ROLLFILM HOLDER ZOOM 2 567.32

The Sinar Zoom 2 Rollfilm Holder is inserted into the camera just like a standard film holder. It is designed for 120- or 220-size rollfilm and it fits all 4x5″/ 10x12.5 cm cameras with an internationally standardized back. The number of exposures depends on the format that has been selected, which can be changed from 4.5x6 cm to 6x12 cm at any time without overlapping images. The design of the holder assures an absolutely flat film plane. Supplied with Vario Mask 534.12 and Universal Mask 534.22.


• You need only this single rollfilm holder and a view camera to cover all current rollfilm picture formats.
• There may be some limitations to the use of these rollfilm holders with certain cameras other than Sinar cameras (Graflock grooves). Please contact us so we can further advise you.

VARIO MASK 534.12

For masking the format in a Sinar Zoom Rollfilm Holder. Adjustable from 4.5x6 cm to 6x12 cm.






SINAR ROLLFILM HOLDER 6x9cm 567.45
SINAR ROLLFILM HOLDER 6x7cm 567.54

Sinar 6x9 cm and 6x7 cm Rollfilm Holders are inserted into the camera just like normal sheet film holders and they fit all 4x5″/10x12.5 cm cameras with internationally standardized backs. They are designed for 120- and 220-size rollfilms, for 8 and 16 or 10 and 20 exposures,
respectively. The design of these rollfilm holders assures excellent film flatness. Supplied with Mask 534.25 for the 6x9cm format, or Mask 534.29 for the 6x7cm format, respectively.

FILM CARTRIDGE 567.92

For use in Sinar rollfilm holders. Individual cartridge for preloading.
Permits quick film change in rollfilm holders.

 

 

HASSELBLAD FILM MAGAZINE ADAPTER 4x5" 556.64.010

Permits the adaptation of the film magazine of a Hasselblad camera to a Sinar camera. This adapter, which is equipped with a coupling device for the film magazine, can be mounted on the Sinar carrier
frame in place of the focusing screen frame. The corresponding format mask, which is to be mounted on the focusing screen together
with a fresnel lens carrier, is included with the adapter.

Focusing Aids

FRESNEL LENS 4x5″/10x12.5 cm 461.76

Brightens the image on the focusing screen, making it considerably easier to view that image, especially with short focal length lenses. Format masks from Set of Masks 534.16 can be inserted in the fresnel lens holder without having to remove the fresnel lens. Easy to snap into Metering Back 4x5″/ 10x12.5 cm 462.16 or into Holder/Focusing Back 4x5″/10x12.5 cm 461.36.

 

FRESNEL LENS 5x7″/13x18 cm 535.17

FRESNEL LENS 8x10″/20x25 cm 535.58

Features similar to those of the of Fresnel Lens 4x5″/10x12.5 cm 461.76. The 535.17 (dimensions: 128x170 mm) fits in Metering Back 5x7″/13x18 cm 462.17 and in any 5x7″/13x18 cm Sinar Holder/Focusing Back. The 535.58 (dimensions: 216x265 mm)
fits in Metering Back 8x10″/20x25 cm 462.58.

SET OF MASKS 534.16

Transparent yellow masks for outlining the image format on a focusing screen when several formats are being used. Fits in Fresnel Lens Frame 461.76. Includes masks for 6x6, 6x7, 6x9 and 10x12.5 cm formats.

MAGNIFIER 4x 531.11.001

Aspherical color-corrected focusing magnifier with 4x magnification.
Viewing area: 45 mm (13/4″) ∅.
Individual viewing sharpness can be adjusted with a focusing ring.
• Can be used for checking the image on a focusing screen and also for viewing color transparencies or reflection prints.

 

BINOCULAR MAGNIFIER 471.21

Can be attached to any Sinar bellows with a 4x5″/10x12.5 cm frame for viewing the image on the focusing screen. With the magnifier swung in, the image on the screen is magnified 2x. In order to avoid false measurements, Binocular Light Hood 531.51 is required for shielding the focusing screen from extraneous light
during TTL exposure metering.
• Joint Rod 472.51 is recommended for attaching the bellows.

BINOCULAR REFLEX MAGNIFIER 4x5″/10x12.5 cm 531.12

Permits viewing of a right-side-up image on the focusing screen with a choice of normal size or 2x magnification. The mirror is adjustable for best possible viewing of the image on the focusing screen. This is particularly important when it is being
used in conjunction with a fresnel lens. Requires the use of Binocular Light Hood 531.51. For farsighted persons, a Pair of Loupes with 4.25 Diopters 531.12.001 is available.

BINOCULAR LIGHT HOOD
531.51

For viewing the image on a focusing screen with Binocular Magnifier 471.21 or Binocular Reflex Magnifier 531.12 without the interference of extraneous light. Has a flap to prevent stray light from affecting the accuracy of TTL exposure measurements.

 

 

PAIR OF LOUPES 4.25 Diopters 531.12.001

For insertion into Binocular Magnifier
471.21 or Binocular Reflex Magnifier
531.12 as eyesight correction for far-
sighted persons.
Special tools and instructions for installation included.

Other Accessories

SINAR p3/f2 CASE 466.010
Designed for the safe transportation of a Sinar f2 4x5″/10x12.5 cm camera with an attached Sinar/Autoaperture behind-the- lens shutter or for use as a case for accessories.
Dimensions: 435 x 340 x 280 mm (17 x 13 x 11″).
Weight when empty: approximately 4.5 kg (10 lb).




SINAR CASE 475.26
Accommodates a – Sinar p2 4x5″/10x12.5 cm or a Sinar x 4x5″/10x12.5 cm basic outfit or a – Sinar f2 4x5″/ 10x12.5 cm basic or
expert outfit, or a – Sinar f1.
This case can also be used for safe storage of lenses, Sinar format adapters, Sinar exposure meters, etc.
Dimensions: 525 x 455 x 305 mm (21 x 18 x 12″).
Weight (empty): approximately 8 kg (17 lb 11 oz).


SINAR EXPERT CASE 475.42
The walls of this case are made of temperature resistant high-density polyethylene to protect the camera during rough transportation (like air baggage handling or off-road travel).To ensure the safety of the camera and its accessories during transportation, the case is lined with an appropriate foam material that is custom-tailored to its contents. The case is equipped with a full-length hinge, two rugged latches, loops for a padlock, three folding handles and four removable rollers. It can hold the basic or the expert outfit of a: – Sinar p2 4x5″/10x12.5 cm or Sinar p2 5x7″/13x18 cm or Sinar p2 8x10″/20x25 cm or – Sinar f2 5x7″/13x18 cm or Sinar f2 8x10″/20x25 cm.
Additional accessories, like Sinar shutters, exposure meters, film holders, etc. can also be accommodated.
Dimensions: 640 x 500 x 380 mm (26 x 20 x 15″). Weight (empty): approximately 11.5 kg (25 lb 6 oz).


DUST COVER 571.52

For the protection of camera set-ups indoors or outdoors.





SEMI REFLECTING MIRROR 5x5″/12x12 cm 539.11
Sinar 50% semi reflecting mirror in a protective case. Helps to solve illumination problems in close-up photography. Serves to project a scene on a backdropfor front projection photography. Also useful for implementing many new ideas for special effects photography. Mirror size: 5x5″/12x12 cm. Fits on all Sinar x5″/10x12.5 cm standards.




FORMAT REDUCTION ADAPTER — From: 5x7″/13x18 cm To: 4x5″/10x12.5 cm 553.27
Reduces the picture format from 5x7″/ 13x18 cm to 4x5″/10x12.5 cm without changing the carrier frame or the rear standard.
Requires the addition of Metering Back 4x5″/10x12.5 cm 462.16, or Holder/Focusing Back 4x5″/10x12.5 cm 461.36.
• The swing and tilt axes do not lie in the film plane, and wide angle camera adjustments are limited.FORMAT




REDUCTION ADAPTER — From: 8x10 /20x25 cm To: 4x5 /10x12.5 cm 553.58
Use this format reduction adapter when you wish to make an inexpensive test shot on 4x5″/10x12.5 cm film instead of the more costly 8x10″/20x25 cm film, without having to refocus and without
having to change the carrier frame or the rear standard.
Requires the addition of Metering Back 4x5″/10x12.5 cm 462.16, or Holder/Focusing Back 4x5″/10x12.5 cm 461.36.
• The swing and tilt axes lie in the film plane, and wide angle camera adjustments are not restricted.

Rail Units

BASIC RAIL 12″/30 cm 422.21
As many extensions as desired can be attached to either side (black end) of a basic rail, but it cannot be used as a rail extension itself. The 12″/30 cm Basic rail is supplied with every Sinar camera.



RAIL EXTENSION 6″/15 cm 421.21
RAIL EXTENSION 12″/30 cm 423.21
RAIL EXTENSION 18″/45 cm 424.21
For lengthening the optical bench by 6″/15 cm, 12″/30 cm or 18″/45 cm, respectively. As many extensions as desired can be attached to the red end.
• With the Special Rail Cap 428.31, these rail extensions can also be used as basic rails.






RAIL CAP 429.21
End caps for Basic Rail 30 cm (12″) 422.21 and for the long Basic Rail 90 cm (36″) 425.21, as well as for the red ends of rail extensions. Prevents unblocked standards from sliding off the rails.



SPECIAL RAIL CAP 428.31
Prevents unblocked standards from sliding off the rail when rail extension 423.21 or 424.21 is being used as a basic rail.

Shutters
Sinar m
Whether it is used as a view camera shutter or as a compact professional camera, the Sinar m is a modern, fast and fully electronically controlled focal plane shutter that is highly effective in every situation.

The Sinar m Becomes a View Camera
The Sinar m also provides the photographer with a modern shutter system for the Sinar p3 view camera. All functions of the camera can be controlled directly from the Sinar m and also via the Sinar CaptureShop™ exposure software. The proven Sinaron Digital Lenses, built into the Sinar Electronic Aperture Control (CAB) mounts, can also be controlled by means of the operating elements of the Sinar m as well as via the exposure software. This represents a significant advantage for the user, especially with an elevated camera position, as in reproduction applications.
With shutter speeds up to 1/2000 second, the Sinar m is the fastest view camera shutter altogether. That, combined with the Sinar p3, makes the Sinar m the perfect system for everyday use in the studio and also on location.

Everything Under Your Control...
Regardless of whether you happen to be positioned at your computer or at the camera, you always have your system under complete control. Every setting that you can make on the Sinar m can also be made by means of the Sinar CaptureShop™ exposure software (requires version 5.2 or higher). The camera system can thus be controlled entirely from the computer and CaptureShop reacts to virtually every input on the camera. Setting changes are synchronized between the computer and the camera, so that accidental operation is impossible. This logical and highly efficient integration is an incalculable advantage for the user that systems assembled with components from different manufacturers cannot offer at all or at best only incompletely.
Accessories * Mirror Module Sinaron Digital AF
* Prism viewfinder, medium format
* Waist-level viewfinder, medium format
* Mirror Module Nikon
* Prism viewfinder 35 mm
* Waist-level viewfinder 35 mm
* Battery PowerGrip
* Manual cable release
* Hand strap
* Neck strap
* Flash accessory rail
* Quick clamping adapter for Sinar p / p2 / p3
* Lens hoods for Sinaron Digital AF lenses
* Lens extension tubes for Sinaron Digital AF

Applicable Lenses
The following lenses can be used on the Sinar m: * Sinar m combined with a Sinar p3: Sinaron Digital CAB lenses 28 to 210 mm and Sinaron Digital CMV lenses 28 to 180 mm
* Sinar m with Sinaron Digital AF Mirror Module: Sinaron Digital AF lenses 40 to 180 mm and a large variety of lenses from the Hasselblad V System
* Sinar m with Nikon Mirror Module: All Nikon lenses for 35 mm cameras with apertures that can be set manually on the lens

Technical Data * Applications: As a multifunctional shutter and control module on Sinar view cameras, or as a self-standing camera module with modern lenses with automatic and/or manual focusing.
* Shutter Type: Fully electronically controlled, vertically operating focal plane blade shutter.
* Shutter Speeds: From 1/2000 second to 68 minutes (depending on the configuration).
* Flash Sync Speed: 1/100 second
* Shutter Delay: Typically 100 msec, in the Ultrafast Mode 5 msec
* Shutter Size: 56 x 42 mm
* Shutter Life: At least 50,000 iterations
* Display: Liquid Crystal Display (LCD) with blue background illumination
* Operation: By means of the LCD with a user-friendly menu structure, dedicated rocker keys and setting dials
* Tripod Socket: 2x 3/8"
* Power Supply: 12 Volt DC
* Dimensions: 180 x 140 x 67 mm
* Weight: 720 g

Sinar Auto Aperture Shutter
The Sinar Auto Aperture Shutter lets you concentrate more on your shooting and less on the mechanical camera operation. Control all operations from behind the camera where you should be. No more having to kneel down in front of your camera to see if the shutter is closed, stopped down or even cocked.



Features:
The shutter is always fully open so you have maximum brightness on the ground glass.

• When you insert a film holder into the back of the camera, the shutter automatically closes down - no more lost sheets of film!
• Automatically self-cocking.
• Shutter speeds from 1/60 to 8 seconds plus B.
• Aperture control from f/4 to f/45 (higher apertures controlled through DB-manual mount).
• Includes a filter holder which accepts up to three 100 mm filters inside the camera.
• To be used with the Auto Aperture Shutter, lenses must be mounted in the Sinar DB mount. If you already have lenses in between-the-lens shutters they can easily be converted.
• Both, the Sinar Auto Aperture Shutter and the Sinaron DB lenses require a 4x5" camera standard.
  
  

Between-the-lens Shutters
Between-the-lens Shutters are mechanical units that are integrated into the lens mount, between the two lens barrels. Mechanical Copal between-the-lens shutters have to be set from the front of the camera, and they have to be closed before the dark slide is removed from a film holder. They also have to be cocked before each exposure. The fact that each shutter has certain individual tolerances can lead to differences in exposure times when lenses are changed. This shutter is available in three sizes: 0, 1, and 3. The size required is depending on the design of the used lens. The available aperture is also depending on the used lens. The minimum shutter speeds are:
Size 0: 1/400 sec.
Size 1: 1/250 sec.
Size 3: 1/125 sec.

Standards & Focusing Backs

FRONT STANDARD p2 431.51
Lens standard for the Sinar p2 with shift mechanisms and asymmetrical swing and tilt capabilities. Equipped with self-locking fine adjustment drives and designed for ergonomic operation.

• Special Front Standard p2 431.52 is recommended when the 8x10″/20x25 cm format is used frequently.

 

BEARER p2 433.51
Lower portion of the rear standard of the Sinar p2, with shift mechanisms, asymmetrical swing and tilt capabilities and a depth of field scale. Equipped with self lockingfine adjustment drives and designed for ergonomic operation. Depending on the format being used, Carrier Frames 4x5″/10x12.5 cm, 5x7″/13x18 cm or 8x10″/20x25 cm (433.26/.27/.58), or correspondent digital adapters (see separate print “Digital Performance”) can be mounted on this bearer.
• The use of this bearer (in conjunction with the appropriate carrier frame) in place of a regular Sinar f2 Rear Standard, can significantly increase the ease of operating a Sinar f2 Camera because of the asymmetrical swing and tilt capabilities.
• Special Bearer p2 433.52 is recommended when the 8x10″/20x25 cm format is used frequently.


CARRIER FRAME 4x5″/10x12.5 cm 433.26
Upper portion of the rear standard of the Sinar p2 and the Sinar e 4x5″/10x12.5 cm!! Fits on Bearer p2 433.51, Special Bearer p2 433.52, Bearer e 433.11 and Special Bearer e 433.12.
• Also available for the larger formats of Sinar p2 and Sinar e Cameras: for 5x7″/13x18 cm 433.27, for 8x10″/20x25 cm 433.58





FRONT STANDARD x 431.71
Lens standard of the Sinar x with shift mechanisms and asymmetrical swing and tilt capabilities. Equipped with self-locking fine adjustment drives and designed for ergonomic operation.








MULTIPURPOSE STANDARD 4x5″/10x12.5 cm 437.61
This is the most frequently used standard for supporting a professional bellows lens hood. It also serves as an intermediate support for long bellows extensions, or as an object stage and a holder for the Sinar Color Control Filter System and for Sinar mirrors, etc. Has shift, swing and tilt capabilities.








METERING BACK 4x5″/10x12.5cm 462.16
This metering back is used with Carrier Frame 4x5″/10x12.5 cm 433.26 of the Sinar p2 and with the rear standards of the Sinar x 433.76, the Sinar f2 and f1 (433.66 and 433.66.001, respectively). It consists of Metering Holder Frame 4x5″/10x12.5 cm 462.96, Focusing Frame 2 461.56 and Focusing Screen 536.66. • Fresnel Lens 461.76 is recommended for focusing, especially with smaller for- mats of the Set of Formats 534.16. • The probe housing of the metering holder frame accommodates any of the metering probes (Sinar Expolux Booster, Sinar Booster 1, Sinar FCM-Booster, Sinarsix-Digital, Profi-select TTL). This metering back permits accurate metering of subject points without causing the image to become unsharp, as it would when a light meter cassette is inserted.


HOLDER/FOCUSING BACK 4x5″/10x12.5 cm 461.36
Holder and focusing screen without probe housing. Fits Carrier Frame 4x5″/ 10x12.5 cm 433.26 of the Sinar p2 and Rear Standard 433.76 of the Sinar x and 433.66 of the Sinar f2. Consists of Holder Frame (without probe housing) 4x5″/10x12.5 cm 461.46 and Focusing Frame 2 461.56 with Focusing Screen 536.66. • Fresnel Lens 461.76 is recommended for focusing, especially with smaller for- mats of Set of Masks 534.16. • The use of an exposure metering probe (Sinar Booster 1 or Sinar Expolux Booster) requires Metering Back 4x5″/10x12.5 cm 462.16.

 

Sinar Sliding Adapter 100 — also suitable for use with Third-party Digital Backs!

A new model of the Sinar Sliding Adapter 100 is now available.
This sliding adapter, which comes in different versions, can be mounted on any Sinar p, p2, and p3 view camera. Sinarbacks and non-Sinar digital backs that are equipped with a dedicated camera interface for Hasselblad H, Contax 645 AF, Hasselblad V, or Mamiya 645 AF can be used.
Sinarback eMotion models can be used with any of the available interface versions.
Sinarback eVolution and Sinarback 54 MC require the Hasselblad V interface version.

Thanks to the sliding adapter's snap-in mechanism digital backs can easily be turned from landscape to portrait without the need of any tools. The 6x6 cm focusing screen is marked with the Sinar p's swing and tilt axes, which allow for quick and precise Sinar p 2-point sharpness adjustment.

An optional 3X magnifier can easily be placed over the focusing screen allowing for a clear and contrasty viewing image of the subject.

Item No.	Description	Scope of Delivery	For use with...
551.32.094	Sliding Adapter 100 HB-V, 54 M/75 H/86 H	- New Sliding Adapter 100 - Interface Plate for Hasselblad V - Adapter Plate for Sinarback 54 M/75 H/86 H - Sinarback Auto Release Cable	Sinarback 54 M Sinarback 54 MC Sinarback eVolution 75 H Sinarback eVolution 86 H
551.32.095	Sliding Adapter 100 HB-V, basic	- New Sliding Adapter 100 - Interface Plate for Hasselblad V	Hasselblad, Leaf, and Phase One digital backs that are fitted with an interface for Hasselblad V
551.32.096	Sliding Adapter 100 HB-V, eMotion	- New Sliding Adapter 100 - Interface Plate for Hasselblad V - Adapter Plate for Sinarback eMotion - Sinarback Auto Release Cable	Sinarback eMotion 22 Sinarback eMotion 54 LV Sinarback eMotion 75 Sinarback eMotion 75 LV
551.32.097	Sliding Adapter 100 HB-H, basic	- New Sliding Adapter 100 - Interface Plate for Hasselblad H	Hasselblad, Leaf, and Phase One digital backs that are fitted with an interface for Hasselblad H
551.32.098	Sliding Adapter 100 Mamiya AF, basic	- New Sliding Adapter 100 - Interface Plate for Mamiya 645 AF	Hasselblad, Leaf, and Phase One digital backs that are fitted with an interface for Mamiya 645 AF
551.32.099	Sliding Adapter 100 Contax AF, basic	- New Sliding Adapter 100 - Interface Plate for Contax 645 AF	Hasselblad, Leaf, and Phase One digital backs that are fitted with an interface for Contax 645 AF

Prices:
551.32.086 Focusing Magnifier 2 $ 1,116.50
551.32.094 Sliding Adapter 100 HB-V, 54 M/86 H $ 5,775.00
551.32.095 Sliding Adapter 100 HB-V, basic $ 4,697.00
551.32.096 Sliding Adapter 100 HB-V, eMotion $ 5,775.00
551.32.097 Sliding Adapter 100 HB-H, basic $ 4,697.00
551.32.098 Sliding Adapter 100 Mamiya AF, basic $ 4,697.00
551.32.099 Sliding Adapter 100 Contax AF, basic $ 4,697.00
551.34.096 Sliding Adapter 100 Hy6, basic $ 4,944.50

551.32.291 Sliding Adapter Interface HB-V $ 803.00
551.32.292 Sliding Adapter Interface HB-H $ 803.00 $ 7 30.00
551.32.293 Sliding Adapter Interface Mamiya 645AF $ 803.00
551.32.295 Sliding Adapter Interface Sinar Hy6 $ 1,221.00
551.43.059 Sinarback Auto Cable Release $ 363.00

Warranty
Supplied with Sinar 1-year warranty
Prices subject to vary without notice